McAfee M4050 - Network Security Platform Guía de usuario

M-3050/M-4050 Sensor Product GuideRevision BMcAfee® Network Security Platform

M-3050 M-4050Dual power supply Dual power supply3 Fan units (that are field replaceable) 3 Fan units (that are field replaceable)It has 2 XLRs (A/B) h

Item Description10 10/100/1000 Management port11 Back panel LEDs (3)1Power Supply A. Power supply A is included with each Sensor. The supply uses a st

LED Status DescriptionPwr A (Power A)OK~ACGreenAmberGreenPower Supply A is functioning.Power Supply A is not functioning.Power Supply in AC mode.Pwr B

The three back panel LEDs provide information regarding the Sensor fans.LED Status DescriptionFan LED OFF The fan is functioning properly.Amber The fa

1OverviewM-3050/M-4050 physical description14McAfee® Network Security Platform M-3050/M-4050 Sensor Product Guide

2Before you installThis chapter describes the best practices for deployment of Sensors in your network. Topics includethe safety considerations for ha

Warnings:• Read the installation instructions before you connect the system to its power source.• To remove all power from the Sensor, unplug all powe

Contents of the boxThe following accessories are shipped in the Sensor box:• One Sensor.• One power supply.• Two CD-ROMs containing the Sensor softwar

2Before you installUnpack the Sensor18McAfee® Network Security Platform M-3050/M-4050 Sensor Product Guide

3Setting up the SensorThis chapter describes how to set up the Sensor for you to configure it.Contents Setup overview How to position the Sensor

COPYRIGHTCopyright © 2014 McAfee, Inc., 2821 Mission College Boulevard, Santa Clara, CA 95054, 1.888.847.8766, www.intelsecurity.comTRADEMARK ATTRIBUT

Install the rails and ears on the chassis and rackBefore you beginBefore you install the rails and ears on the chassis, make sure that the power is of

Because of the weight of the appliance, McAfee recommends that two people remove the chassis fromthe rail cabinet. When removing the chassis from the

3Place the power supply in the slot with the cable outlet facing front and on the left side of thefaceplate.Figure 3-3 Installing the power supply4Sl

Small form-factor pluggable modulesThe Sensor uses two types of small form-factor pluggable modules as shown in the following table:Type PerformanceSF

XFP modulesThe supported XFP module is a robust small form-factor pluggable, operating at 850nm, for up to 10gigabits per second on SONET/SDH, Fibre C

Remove a modulePerform these tasks if you need to remove an SFP or XFP module.Task1Disconnect the network fiber-optic cable from the module.2Release t

3Setting up the SensorPower off the Sensor26McAfee® Network Security Platform M-3050/M-4050 Sensor Product Guide

4Attaching Cables to the SensorFollow the steps outlined in this chapter to connect the cables to the various ports of your Sensor.Contents Cable t

2Connect the other end of the Console cable directly to a COM port of the PC or terminal server youwill use to configure the Sensor, for example, a PC

About the fail-open portFail-open functionality for the GE Monitoring ports is accomplished using the standard GigabitFail-open Bypass Kit, which is s

ContentsPreface 5About this guide ... 5Audience ... 5Conventions ...

Port Pairs (and Transceiver Type)5A and 5B (SFP)6A and 6B (SFP)You cannot configure, for example, IA and 2A to work together as a pair.Figure 4-1 Usi

Task1Plug the cable appropriate for use with your Gigabit Ethernet into one of the Monitoring ports, forexample 1A.2Plug another cable into the peer o

Task1Plug the cable appropriate for use with your XFP module into port 2A of the active Sensor.2Connect the other end of the cable to port 2A of the s

continues to flow through the network link but is no longer routed through the Sensor. Once theSensor resumes normal operation, the switch returns to

4Attaching Cables to the SensorHow does the fail-open function work34McAfee® Network Security Platform M-3050/M-4050 Sensor Product Guide

5Troubleshooting the SensorThis section lists some common installation problems, the possible causes, and the correspondingsolutions.Problem Possible

5Troubleshooting the Sensor36McAfee® Network Security Platform M-3050/M-4050 Sensor Product Guide

6Sensor technical specificationsThe following table lists the specifications of the Sensor:Sensor Specifics DescriptionDimensions Without mounting ear

Sensor Specifics DescriptionSystem Heat Dissipation AC (max): 535W, 1825 BTU/hrDC (max): To Be determinedAirflow 200 lfm (1 m/s)Altitude Sealevel to 1

ARegulatory, compliance, and safetyinformationThe Sensor meets the following standards:Sensor regulatory, safety, and complianceRegulatory: Products w

About the fail-open port ...29Cable the Management port ... 29About connecting cables to the Mon

Sensor regulatory, safety, and compliance• Radiated Emissions• Conducted Emissions• EN 61000-3-2: 2000 Harmonic Current Emissions• EN 61000-3-3: 1995

IndexAabout this guide 5Auxiliary port 28CCable types for switches 30Cabling for In-line mode 30Cabling for SPAN 15, 31, 32Cabling for TAP mode 31Cabl

700-3589B00

PrefaceThis guide provides the information you need to configure, use, and maintain your McAfee product.Contents About this guide Find product d

Tip: Suggestions and recommendations.Important/Caution: Valuable advice to protect your computer system,software installation, network, business, or d

1OverviewThis chapter provides an overview of McAfee® Network Security Sensors in general and the M-3050/M-4050 Sensor model in particular.Contents

Functions of a SensorThe primary function of a McAfee® Network Security Sensor (Sensor) is to analyze traffic on selectednetwork segments and to respo

Following is an example of a network topology using Gigabit Ethernet throughput. In the illustration,McAfee® Network Security Platform (formerly McAfe